NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 25

Страница: 25 / 112

NAVIGAT X Mk 2

056341 Rev. AA

2: Operation

Page 2-13

2.10.2.5

Settings NAVIPRINT

Sets the parameters for the printout of an act. heading graph using the nav.
data printer NAVIPRINT.

Naviprint

Function:

Switches printing on/off.

Settings: ON

output to printer active

OFF

no output to printer

Pap.

Speed

Function:

Sets the paper feed speed for the heading graph.

Settings: 60 mm

print at 60 mm/h (1 cm = 10 min.)

150 mm

print at 150 mm/h (1 cm = 4 min.)

600 mm

print at 600 mm/h (1 cm = 1 min.)

Hdg

Function:

Sets the horizontal scaling of the heading graph.

Settings: ±30°

scale to show 30° to the left and to the right from the graph’s center
(current print position shifts to center when graph margin is
reached)

±180°

scale to show 180° to the left and to the right from the graph’s
center (current print position shifts to center when graph margin is
reached)

Note

After any interruption of power, the compass system‘s internal clock must be
reset in the user setup in order for date and time to appear correctly on the
printout.

Содержание Sperry Marine NAVIGAT X MK 2
















































































































Результаты поиска

Содержание Sperry Marine NAVIGAT X MK 2

Отзывы:

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренды по названию

Популярные бренды

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Руководство по сборке

Результаты поиска

Содержание Sperry Marine NAVIGAT X MK 2

Отзывы:

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренды по названию

Популярные бренды