NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 112

background image

NAVIGAT X Mk 2

056341 Rev. AA

2: Operation

Page 2-9

2.10.2

Manual Settings – Parameters

2.10.2.1

Speed/Latitude

Sets the parameters for speed and latitude inputs used for the automatic North
speed error correction.

Speed/Lat

Mode

Function:

Selects between automatic and manual input of the actual speed
and latitude.

Settings: Speed Mode

man: speed is entered manually
auto: speed is entered automatically

Posit Mode

man: speed is entered manually
auto: speed is entered automatically

Speed/Lat

Set.

Function:

Enters the manual speed and latitude values.

Settings:

man. spd.: 0.0 – 99.9 kts

man. lat.: 99:99:99 N – 99:99:99 S

Note

Speed and latitude data is transmitted at the sensor data outputs in automatic
mode only.
If speed and/or latitude are entered manually, the respective data must be con-
tinuously updated according to the prevailing conditions.
Manual speed input should be accurate to ±1 kt., manual latitude input should
be accurate to ±1°.

«
...
19
20
21
22
23
...
»

Содержание Sperry Marine NAVIGAT X MK 2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренд: A&D Страницы: 74

Бренд: PASCO Страницы: 3

Бренд: PASCO Страницы: 2

Бренд: NanoPhotometer Страницы: 133

Бренд: G-Tek Страницы: 83

Бренд: Yamaha Страницы: 31

Бренд: Divertug Страницы: 47

K-PATENTS PR-43

Бренд: Vaisala Страницы: 54

Бренд: Hanna Instruments Страницы: 25

Бренд: Proteus Страницы: 4

Friendly Digital Piano Forte PV35

Бренд: Kawai Страницы: 102

Бренд: PTC Instruments Страницы: 2

KS-PH-221-DELUXE

Бренд: Kensington Страницы: 14

Бренд: Cewe Страницы: 8

Бренд: ATIM Страницы: 32

Бренд: Kobold Страницы: 27

Бренд: Zamel Страницы: 2

Бренд: Cal Test Electronics Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды