Northern Amp Arc 7000 Скачать руководство пользователя страница 5

Operating Instructions and Parts Manual 

Northern Industrial Welding 

 

 

 
 
 

Amp Arc 7000 

Amp Arc 7000 

General Safety Information 

1.1 Your Welding Environment 

-Keep the environment you will be 
welding in free from flammable 
materials. 
-Always keep a fire extinguisher 
accessible to your welding 
environment. 
-Always have a qualified person 
install and operate this equipment. 
-Make sure the area is clean, dry and 
ventilated. Do not operate the welder 
in humid, wet or poorly ventilated 
areas. 
-Always have your welder maintained 
by a qualified technician in 
accordance with local, state and 
national codes.            
-Always be aware of your work 
environment. Be sure to keep other 
people, especially children, away 
from you while welding.  
-Keep harmful arc rays shielded from 
the view of others. 
-Keep the welder secure to prevent it 
from tipping over or falling. 

1.2 Your Welder’s Condition 

-Check ground cable and welding 
cable to be sure the insulation is not 
damaged. Always replace or repair 
damaged components before using 
the welder. 
-Check all components to ensure they 
are clean and in good operating 
condition before use. 

1.3 Use of Your Welder 

 

Do not operate the welder if the 
output cable or electrode cable, are 
wet. Do not immerse them in water. 
These components and the welder 
must be completely dry before 
attempting to use them. 
-Follow the instructions in this manual. 

-Keep welder in the off position when 
not in use. 
-Connect ground lead as close to the 
area being welded as possible to 
ensure a good ground. 
-Do not allow any body part to come 
in contact with the welding electrode 
if you are in contact with the material 
being welded, ground or electrode 
from another welder. 
-Do not weld if you are in an awkward 
position. Always have a secure 
stance while welding to prevent 
accidents. Wear a safety harness if 
working above ground. 
-Do not drape cables over or around 
your body. 
-Wear a full coverage helmet with 
appropriate shade (see ANSI Z87.1 
safety standard) and safety glasses 
while welding. 
-Wear proper gloves and protective 
clothing to prevent your skin from 
being exposed to hot metals, UV and 
IR rays. 
-Do not overuse or overheat your 
welder. Allow proper cooling time 
between duty cycles. 
-Keep hands and fingers away from 
moving parts. 
-Do not point electrode at any body 
part of yourself or anyone else.  
-Always use this welder in the rated 
duty cycle to prevent excessive heat 
and failure. 

1.4 Specific Areas of Danger,  
      Caution or Warning

 

 

Electrical Shock 

 

Electric arc welders can 
produce a shock that 
can cause injury or 

death. Touching electrically live parts 

Содержание Amp Arc 7000

















Отзывы: