Northern Lights M673L2 Скачать руководство пользователя страница 10

Страница: 10 / 34

OM673L2 08/05

Operating Procedures

ShUTdOWNS ANd ALARMS

1. Generator sets have shutdown systems to stop the

engine in the event of hight water temperature or low

oil pressure.

a. Other alarms and shutdowns are available as

optional equipment.

NOTE: Do not rely on your warning to the

exclusion of careful gauge monitoring. Watching

your gauges can prevent damage to the unit and

dangerous power losses.

2. Do the following when your warning or shutdown

system is activated:

a. Check the temperature gauge.

If above 205°F (6°C), shut off the

engine immediately.

b. Use the Trouble Shooting Guide on page 25 to

isolate the cause of the overheat.

CAUTION: Do not remove the water fill

cap of an overheated engine. Escaping high

temperature steam can cause severe burns.

Allow the engine to cool and then remove the

cap slowly using protective clothing.

c. Make repairs. Restart your generator set after the

temperature gauge registers below 200°F (°C).

d. Watch the temperature gauge regularly and

turn off the unit if the temperature rises above

205°F (6°C). Repeat troubleshooting.

. If shutdown is activated and the temperature gauge

shows temperature within normal temperature range:

a. Check the engine crankcase oil level.

b. If the oil level is low, fill with recommended

lubricating oil and restart. Watch the oil pressure

gauge carefully and shut off the engine if it does

not show a normal reading (20-60 PSI) after a

few seconds of operation.

c. If the oil level is normal, DO NOT restart the

engine. Call your dealer for assistance.

SPARE PARTS

1. ADE recommends that you keep the following spare

parts on hand for field service. The parts are

available from your local Northern Lights dealer.

Some marine models already have “On-Board-Kits,”

a handy box that contains the most common parts

you will need.

2. All owners should have the following:

a. Primary and secondary fuel filter elements

b. Oil filters

c. Air filter

d. Alternator belt

e. Thermostat and gaskets

f. Raw water pump impeller & gaskets

g. Glow plug

h. Injector and washer

. If your set is operating a long distance from a servic-

ing dealer, add the following:

a. Complete set of injectors

b. Copper washers for injector change

c. Complete set of glow plugs

d. Fuel lift pump

Содержание M673L2



































Результаты поиска

Содержание M673L2

Отзывы:

Похожие инструкции для M673L2

Бренды по названию

Популярные бренды

Northern Lights M673L2, Руководство оператора

Результаты поиска

Содержание M673L2

Отзывы:

Похожие инструкции для M673L2

Бренды по названию

Популярные бренды