Northern Lights Lugger M773LW Скачать руководство пользователя страница 21

Страница: 21 / 31

OM773LW2 10/09

GLOW PLUGS

1. Each cylinder is supplied with a glow plug which

serves to heat the combustion chamber.

2. To check the glow plugs, loosen the current
carrying

fl at wire between the plus-poles of the

glow plugs (

Figure 19

). Connect a D.C. test bulb

between the plus-pole of the battery and the

plus-pole of the glow plug. If the bulb lights up,

the glow plug is functioning properly.

3. Check all glow plugs and replace any faulty ones.

Figure 19: Glow plugs.

BOOSTER BATTERIES

CAUTION: Battery gas can explode.

Keep all fl ames and sparks away from batteries.
Battery electrolyte is sulfuric acid diluted, which
can burn or stain body or clothes.

1. Before changing or using booster batteries, check bat-

tery electrolyte level. Add distilled water if necessary.

2. Booster and main batteries must have the same volt-

age rating.

3. First, connect positive (+) terminal of booster bat-

tery to positive (+) terminal of main battery. Then,
connect negative (-) terminal of booster battery to
ground on the engine block (

see Figure 20

4. Remove booster battery after starting engine.
5. Sealed batteries: See manufacturer charging and

booster instructions.

SP 18-19. BATTERY CARE

1. Check electrolyte level daily, Add distilled water to

manufacturer’s recommended level.

2. Batteries, cables and cable terminals should be

checked and cleaned every 100 hours.

Clean corrosion with a water and baking soda solu-
tion. Flush with clean water. Tighten terminals and
grease them to inhibit corrosion.

3. Check the battery condition with a hydrometer every

250 hours.

SP20. WINTERIZING / OUT-OF-SERVICE

1. Generator

sets:

a. Drain fresh water and seawater cooling systems

completely. Remember to shut off seacocks

before opening drain cocks.

b. Drain water supply lines and wet exhaust line.

c. Loosen the seawater pump cover and drain pump.

d. Fill the fuel tank or add biocide as per

manufacturer’s

instructions.

e. Seal the air cleaner inlet, exhaust opening,

crankcase breather pipe, and fuel tank vent with

plastic bags and tape.

f. Store the set in a dry, protected place. If unit must

be stored outside, be sure it is well protected with

cover.

g. Change the crankcase oil and fi lter.

h. Loosen the alternator belt.

i. Disconnect and clean battery. Remove to warm

storage place if possible.

j. Clean outside of unit. Paint any scratched or

chipped surfaces. Put corrosion preventative on

all exposed metal surfaces.

Figure 20:

Battery connections.

Servicing

Содержание Lugger M773LW
































Результаты поиска

Содержание Lugger M773LW

Отзывы:

Бренды по названию

Популярные бренды

Northern Lights Lugger M773LW, Руководство оператора

Результаты поиска

Содержание Lugger M773LW

Отзывы:

Бренды по названию

Популярные бренды