North Star M157598L.1 Скачать руководство пользователя страница 11

Trailer Safety 

 11

 
Step One.  Inspect/Repair 

 

Trailer must be inspected BEFORE EACH USE.   
 

      WARNING 

 

Read instructions below carefully for 
inspecting and preparing the trailer. 
Damaged or missing components 
could result in injury to the operator, 
bystanders, or property damage. 

 

Important safety rules:

 

• 

Replacement parts.

  If a part needs replacement, 

only use parts that meet the manufacturer’s 
specifications.  Replacement parts that do not meet 
specifications may result in a safety hazard or poor 
operation of the trailer. 

 

Inspect and test the trailer thoroughly 

1.  Check tires for proper pressure level. 
2.  Check to be sure that all nuts and bolts are tight. 
 
 
 

Step Two: Towing the pressure washer 
trailer. 

 
1.  Review the “Operation – Important Safety     
Information”

 related to Transportation Safety provided 

in this manual. 
 
 

2.  Attach Pressure washer to vehicle hitch 

a.  Attach trailer’s coupler to a class 4 or higher hitch 

with 2” ball (only).  

b.  Make sure coupler is installed completely and 

insert safety pin.  

 

Important:  

When filled, the trailer sprayer has a tongue 

weight of approximately 400lbs.  Ensure that the tow 
vehicle is properly equipped to handle this load. 
 

3.  Attach safety cables and lights. 

Two safety cables must be used while towing. 

    

 Attach breakaway switch. 

 

Pull pin out of breakaway switch and route through 
safety cable latch point, then through the cable loop.  
Re-insert the cable into the switch. 
 

 
 

 
 
Important:  

When not towing the trailer the pin must 

be installed in breakaway switch.  Failure to have pin 
installed will drain your pressure washers battery.  
Never use breakaway switch as a parking brake.  

     

Attach 

lights. 

 

   Plug 7-way pin connector into vehicle. 

 
4.  Put jack up 
     

Crank the jack into the up position before towing. 

 
 

5. Transport 

It is recommended that the pressure washer 
trailer be towed at speeds less than 60mph. 

 

Important safety instructions

• 

Added length

.  Be aware of the added length of 

the sprayer.  

• 

Rough terrain

.  Drive slowly and take extra 

caution when traveling over rough terrain.   

• 

On public roads

.  When towing on a public 

road, make sure to comply with all local, state, 
and federal towing requirements.  It is the sole 
responsibility of the purchaser to obtain licensing 
and signage, as needed to comply. 

• 

Unattended

.  Turn off the towing vehicle before 

leaving the trailer unattended.

 

• 

Under the influence

.  Never tow or operate this 

pressure washer while under the influence of 
alcohol, drugs, or medication

.

 

   
 
 
6.  Leaving unattended 

If the trailer must be left unattended at any time

:  

• 

Turn off the vehicle.  Set brake or block the   

wheels.

Содержание M157598L.1





























Отзывы: