manualshive.com logo in svg

North Star 157597, Руководство пользователя, Страница: 51 / 66

Поделиться
Скачать
North Star 157597 Скачать руководство пользователя страница 51

Troubleshooting 

 

51 

 

 
 
 

Engine Will Not Start 

Causes 

Solutions 

Low Oil Shutdown 

Fill engine with the adequate amount of oil. 

Cold Engine 

Choke engine to start. 

No Fuel 

Add gas to engine; make sure fuel shutoff valve is open. 

Dead Battery 

Recharge/Replace battery. 

Spark plug wire not attached 

Attach spark plug wire to spark plug. 

 

Pressure Washer Runs But Burner Doesn't Fire

 

Causes

 

Solutions

 

Heat switch turned OFF 

Turn heat switch ON. 

Thermostat set too low or off 

Set thermostat to desired temp. 

Fuel tank empty  

Fill fuel tank with kerosene, diesel, or fuel oil. 

Defective Flow Switch 

Clean flow switch. See Maintenance and Repair section for 
instructions. 

Defective Thermostat 

Call Product Support. 

Defective Burner 

Call Product Support. 

 

Pressure Washer Runs But No Pressure

 

Causes

 

Solutions

 

Partially clogged or damaged nozzle 

Clean or replace nozzle. 

Clogged water filter 

Clean water filter. 

Improper nozzle combinations  

Use proper nozzle configurations as stated in manual  

Low water flow 

Check for kinked suction line   

 

Smoke From Heat Exchanger

 

Causes

 

Solutions

 

Air band not adjusted properly 

Adjust the air band until the burner burns cleanly. See 

Installation 

Instructions

 

Poor quality fuel 

Use kerosene for the cleanest burn. 

 

Water Not Heating Sufficiently

 

Causes

 

Solutions

 

Scale build-up in coil 

See 

Coil Descaling

 under 

Maintenance Instructions.

 

Coil is full of soot 

Call Product Support. 

 

Poor Or No Detergent Supply

 

Causes 

 

Solutions

 

Soap control knob set too low. 

Adjust soap control knob. 

Inadequate detergent supply 

Refill detergent container. Make sure chemical strainer is fully 
submerged. 

High pressure hose too long 

Use less hose.  Move machine closer to the work. 

Chemical strainer or injector clogged  Clean the strainer and injector. Always start with a clean detergent 

container. Run clean water through the injector after each use. 

Содержание 157597



































































Отзывы:

Нет отзывов