North Atlantic SRS 5330A Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

North Atlantic SRS 5330A Скачать руководство пользователя страница 17

North Atlantic Industries, Inc.

631.567.1100 / 631.567.1823 (fax)

6/12/2018

5330A Operations Manual Rev A6

110 Wilbur Place, Bohemia, NY 11716

Cage Code: 0VGU1

Page 17 of 24

The

Calibration Menu,

shown below

,

contains a calibration routine for the Touch screen display and a calibration

routine for the Instrument.
The

“Touchscreen Calibration” will give prompts to the user to touch the screen at various places in order to

correctly center the screen. At the end,

“Calibration Complete” will be displayed.

The

“Unit Calibration” will perform a full, ‘off-line’ self-calibration that does not require user intervention or external

equipment; duration is approximately 25 minutes.

Figure 23

– Calibration Menu

Shown below are examples of the

Help Menu

screens. The help menu gives things such as specification

summaries, descriptions of available buttons and descriptions of available functions. The Help Menu screen
shows the unit’s serial number, date code, MAC address, model information and firmware revision.

Figure 24

– Help Menus

Default Values

screen enables user to restore the 5330A factory settings.

Figure 25

– Default Values

«
...
15
16
17
18
19
...
»

Содержание SRS 5330A

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды