background image

8807560          05/13

18 GAUGE FLOORING STAPLER

SPECIFICATIONS
Minimum Operating Pressure:

60 PSI

Maximum Operating Pressure:

100 PSI

Stapler Size: 

18 gauge

Staple Length:

 3/8 in. - 1/4”

Magazine Capacity: 

100 nails

Air Inlet: 

 1/4 in.

Air Consumption:

 1 CFM

CAUTION:
FOR YOUR OWN SAFETY READ
INSTRUCTION MANUAL
COMPLETELY AND
CAREFULLY BEFORE
OPERATING THIS FLOORING
STAPLER.

Any failures made in following
the safety regulations and
instructions may result in an
electric shock, fire and/or
serious injury.

SAFETY INSTRUCTIONS

 

KEEP WORK AREA CLEAN.

Cluttered areas invite injuries.

• DON’T ALLOW CHILDREN
AROUND THE WORK AREA.
Do not let children handle the
tool.

• DO NOT OPERATE THIS
TOOL IF UNDER THE
INFLUENCE OF ALCOHOL OR
DRUGS. Read the warning
labels on prescriptions to
determine if your judgment or
reflexes are impaired while
taking drugs. If there is any
doubt, do not attempt to
operate.

• USE SAFETY GLASSES.
Safety glasses should conform
to ANSI z87.1 specifications.
Safety glasses should be worn
against flying to debris from the
front and side. Safety glasses
should be worn when loading,
operating, unloading, or
servicing the tool.

• USE EAR PROTECTION. The
working area may be exposed to
high noise levels that can lead
to hearing damage.

• NEVER USE OXYGEN,
COMBUSTIBLE GASES,
BOTTLED GASES, OR HIGH

Models: 7560

For Customer Service, please call 

1-800-348-5004

 or 

email 

[email protected]

CALIFORNIA PROPOSITION 65

WARNING: You can create dust
when you cut, sand, drill or grind
materials such as wood, paint,
metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer,
birth defects, or other
reproductive harm. Wear
protective gear.

WARNING: This product or its
power cord may contain
chemicals, including lead, known
to the State of California to cause
cancer and birth defects or other
reproductive harm. Wash hands
after handling.

Important!

When using equipment, a few safety
precautions must be observed to
avoid injuries and damage. Please
read the complete operating manual
with due care. Keep this manual in a
safe place, so that the information is
available at all times. If you give the
equipment to any other person, give
them these operating instructions as
well. We accept no liability for
damage or accidents which arise due
to non-observance of these
instructions and the safety
information herein.

1

Содержание 7560








Отзывы: