Nortel Passport 8002PS Скачать руководство пользователя страница 6

2

 

Preparing Cables

Required tools: Crimping tool for crimping lugs onto cables; heat gun

Nortel Networks does not supply the cables for connecting the Passport 8002PS DC Power Supply to 
the DC input power source. You can therefore select cables that comply with the electrical code of the 
country where you intend to use the DC power supply. 

The following items are shipped with the Passport 8002PS DC Power Supply:

To select and prepare cables for connecting the power supply, use the following guidelines:

Two 2-hole crimp lug terminals with attached heat-shrink 
tubing (1) for connecting the positive and negative power 
inputs

One 1-hole crimp lug terminal with attached heat-shrink 
tubing (2) for connecting the ground stud

Five lock washers for connecting all leads

One lock washer for connecting the ground stud

Caution: 

As the installer, you have the sole responsibility to ensure that the connection 

cable used with the Passport 8002PS DC Power Supply is appropriate for use with the DC 
power source to which the power supply is connected. Consider gauge, flammability, and 
mechanical serviceability when determining which cables to use.

Use a 6-gauge, 3-conductor cable such as an SOW-A, Type 90C 
or equivalent.

1 = Insulated Conductors
2 = Frame Ground
3 = Negative (-)
4 = Positive (+)
5 = Outer Insulation Jacket

Use cable that accommodates the supplied DC input and frame 
ground crimp lugs.

To connect to the positive and negative terminal leads, use the 
two-hole lug terminals (1).

To connect the frame ground lead, use the one-hole terminal (2).

Strip the outer cable jacket to no less than 1 1/2 inch (3.8 cm) to 
expose the insulated conductor cables within.

Strip the insulated conductor cables inside the outer jacket to 
0.81 in (2.1 cm).

Use a standard crimping tool to crimp the lugs onto the cables. 
Failure to properly crimp the lugs onto the cables constitutes a 
safety hazard.

If necessary, use a heat gun to shrink the tubing around the cable.

1

2

9413EB

>1.5 in.

(3.8 cm)

9414EA

1

2

3

4

5

Содержание Passport 8002PS













Отзывы: