manualshive.com logo in svg

Nortel Passport 7400, Установка оборудования, техническое обслуживание и устранение неисправностей, Страница: 407 / 438

Поделиться
Скачать
Nortel Passport 7400 Скачать руководство пользователя страница 407

Chapter 37 Hardware procedures   407

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Setting modem dip switches

Set modem dip switches using the instructions provided by the manufacturer
of the modem before you configure the modem software.

Prerequisites

•

Ensure the modem you want to use supports all of the required settings.
For more information, see “Modem selection” (page 141).

Procedure steps

1

Set the modem dip switches as specified in the table “Modem dip switch
settings” (page 407). The table applies to a US Robotics 56K modem as
an example of the settings you must apply.

Table 9
Modem dip switch settings

Switch
number

Description of the setting

Required setting

 1

modem ignores DTR (override)

on (down)

2

verbal (word) results

off (up)

3

disable word codes

off (up)

4

suppresses echo

on (down)

5

modem answers on first ring, or higher if
specified in non-volatile memory (NVRAM)

off (up)

6

modem sends CD signal when it connects
with another modem, drops CD on
disconnect

off (up)

7

loads Y or Y1 configuration from user-defined
NVRAM

off (up)

8

disables command recognition (dumb mode) off (up)

Содержание Passport 7400























































































































































































































































































































































































































































Отзывы:

Нет отзывов