Nortel Passport 7400 Скачать руководство пользователя страница 370 | Manualshive

Страница: 370 / 438

Nortel Passport 7400 Скачать руководство пользователя страница 370

370 Chapter 37 Hardware procedures

241-7401-240 5.2S1

Removing a Passport cabinet from a pallet

After you unpack a cabinet, remove it from its pallet. If the cabinet is the
seismic version, see the procedure “Unpacking and removing a seismic
cabinet from a pallet” (page 432).

Prerequisites

Procedure steps

1

Remove and keep the packing slips and shipping papers attached to the
outside packaging.

2

Ensure the pallet is on a flat surface.

3

The anchor brackets fasten the cabinet to the pallet with lag bolts. Use an
open-end wrench or socket wrench to loosen the lag bolts. The figure

WARNING

Risk of personal injury

A cabinet that contains one switch weighs 200. kg
(441 lb). You need four people to move this cabinet.

A cabinet that contains two switches weighs 313. kg
(689 lb). You need six people to move this cabinet.

WARNUNG

Verletzungsgefahr

Ein Gehäuse mit einem Switch wiegt 200 kg. Zum
sicheren Bewegen dieses Gehäuses werden vier
Personen benötigt.

Ein Gehäuse mit zwei Switches wiegt 313 kg. Zum
sicheren Bewegen dieses Gehäuses werden sechs
Personen benötigt.

CAUTION

Avoid structural stress when maneuvering uncrated
cabinets and shelf assemblies

When handling and moving uncrated cabinets and shelf
assemblies, avoid strain, excessive shock, or vibrations,
which can damage or warp the equipment.

«
...
368
369
370
371
372
...
»

Содержание Passport 7400























































































































































































































































































































































































































































Отзывы:

Нет отзывов