Nortel Passport 5430 Скачать руководство пользователя страница 93

Страница: 93 / 220

Connecting Cables to the Passport 5430

306308-A Rev 00

4-15

To connect to an integrated V.34 console modem module:

Configure the modem, using the parameters in

Table 4-3

page 4-11

Install the V.34 console modem module in the Remote Console slot.

For instructions, see “Installing a WAN Adapter Module” on page 2-21.

Route the cable through the cable loom slot corresponding to the remote
console slot.

Insert the RJ-11 jack into the Passport 5430 Remote Console interface

(Figure 4-10)

Figure 4-10.

Connecting to an Integrated Console Modem

For more information on the Passport 5430 V.34 console modem module, see the
V.34 Modem Adapter Module Supplement, which Nortel Networks ships in the
adapter module upgrade kit.

FBR0065A

RJ-11 telephone receptacle

Module 3

Module 4

Module 5

Remote
Console

COM

ISDN BRI

with NT1

Telco

V.34 Modem

Содержание Passport 5430





























































































































































































































Результаты поиска

Содержание Passport 5430

Отзывы:

Nortel Passport 5430, Инструкции по установке и эксплуатации, Страница: 93 / 220

Результаты поиска

Содержание Passport 5430

Отзывы: