manualshive.com logo in svg

Nortel Passport 5430, Инструкции по установке и эксплуатации, Страница: 127 / 220

Поделиться
Скачать
Nortel Passport 5430 Скачать руководство пользователя страница 127

Replacing the System Processor Card

306308-A Rev 00

7-3

 

8.

Pull the system processor card toward you to detach it from the system 
processor card connector in the Passport 5430 chassis.

Be prepared to apply some force, but stop pulling as soon as the system 
processor card is free from the system processor card connector.

9.

Slide the system processor card all the way out of the slot.

10.

If a PMC module is installed on the system processor card, remove it. 

a.

Locate the installed PMC module 

(Figure 7-3)

.

b.

Using a Phillips screwdriver, remove the 4 screws that secure the 
PMC module to the system processor card.

c.

Grasping the edges of the PMC module, pull it straight up and lift it 
out of the module socket.

d.

Place the PMC module in an antistatic bag, or set it on an antistatic 
mat.

Figure 7-3.

Locating the PMC Module on the System Processor Card

11.

Place the system processor card in an antistatic bag.

FBR0052A

System 

Processor

PMC module

Flash card slots

Console connector

10/100BASE-TX connectors

Содержание Passport 5430





























































































































































































































Отзывы:

Нет отзывов