Nortel Passport 5430 Скачать руководство пользователя страница 120

Страница: 120 / 220

Installing and Operating the Passport 5430 Multiservice Access Switch

6-10

306308-A Rev 00

Wait 1 minute and then turn the power switch to the on position.

If the problem persists, contact the Nortel Networks Technical Solutions
Center.

Verify that the DC OK LED is on.

To turn off the Passport 5430:

Press the power switch on the power supply to the off (0) position.

If a redundant power supply is installed, turn it off.

Resetting the Passport 5430

The Reset buttons are located inside the Passport 5430 front panel, next to the
console port

(Figure 6-6)

Figure 6-6.

Passport 5430 Reset Buttons

To press one of the Reset buttons, insert a small pointed object (for example, a
paper clip) into the Reset button hole.

FBR0098A

Module 3

Module 4

Module 5

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

Remote
Console

5V FLASH ONLY

PCMCIA 2

Module 2

Module 1

Port 1

Port 2

Insert

Extract

PCMCIA 1

SYNC

LOOP

RED
ALM

TX/RX

SPD

Link

PS1

PS2

Fan

WAN

Mod2

cPCI

Run

Boot

Sys

YEL
ALM

Console

System

Processor

Expansion Card

T1/E1

Dsync

Port 1

Port 2

Port 1

Port 2

Port 1

Port 2

Insert

Extract

Expansion Card

Insert

Extract

Module 2

Module 1

Module 2

Module 1

Module 2

Module 1

Voice Processor

Dsync

COM

RLSD

Serial

ISDN BRI

withNT1

Daul

T1/E1

SYNC

LOOP

RED
ALM

YEL
ALM

SYNC

LOOP

RED
ALM

YEL
ALM

Telco

RLSD

DTR

V.34 Modem

COM

RLSD

Serial

Port 2

Hard reset

Soft reset

Содержание Passport 5430





























































































































































































































Результаты поиска

Содержание Passport 5430

Отзывы:

Nortel Passport 5430, Инструкции по установке и эксплуатации, Страница: 120 / 220

Результаты поиска

Содержание Passport 5430

Отзывы: