Nortel Passport 4400 Series Скачать руководство пользователя страница 81

Страница: 81 / 144

Analog Voice Modules

Passport 4400 Hardware Installation Manual

8-3

Removing an Interface Module

Procedure 13: Removing an interface module

Facing the rear of the voice/fax module, remove the screw on the left side of

the connector cover with the Phillips screwdriver (refer to Figure 8-4).

Unhinge the right tab from the slot on the right side of the interface module,

then remove the connector cover. Save the screw.

Disconnect any modular cables from the RJ11 connectors or unplug the
terminal block from the interface.

Unscrew the two spring-loaded captive screws with the medium-sized,
flathead screwdriver.

Grasp the interface module firmly and slide it slowly toward you until it is
free of the voice/fax module (Figure 8-5).

Figure 8-4. Removing the connector cover

Caution:

The interface modules cannot be inserted into or removed from
the unit while the Passport 4400 is operating. This could cause
damage to the Passport 4400 or interruption of network service
or both.

Connector

Cover

Rear Of Interface

Module

Terminal

Block

RJ11

Connector

Captive

Screw (2)

Retaining

Slot

Left
Tab

Right

Tab

Содержание Passport 4400 Series

















































































































































Результаты поиска

Содержание Passport 4400 Series

Отзывы:

Похожие инструкции для Passport 4400 Series

Бренды по названию

Популярные бренды

Nortel Passport 4400 Series, Руководство по установке оборудования

Результаты поиска

Содержание Passport 4400 Series

Отзывы:

Похожие инструкции для Passport 4400 Series

Бренды по названию

Популярные бренды