Nortel Meridian Скачать руководство пользователя страница 182

Страница: 182 / 256

158

Meridian Digital Telephone IP Adapter Installation and Administration Guide

Troubleshooting

Standard 1.1

Incoming calls are not being
received from the host PBX.
(continued)

The network administrator should check
the IP network (if it is being used) and
ensure that:

it is not down

traffic is being routed between the
Meridian Digital Telephone IP
Adapter unit and RLC on the host
PBX

The network administrator should PING
the RLC from the Meridian Digital
Telephone IP Adapter unit to verify IP
network connectivity.

If the problem persists, contact your
telecom administrator or Nortel
Networks distributor.

A call in progress was
suddenly disconnected.

Does your telephone display “Offline
Mode?” If so, enter the online SPRE
code to go back online.

Contact your telecom and data network
administrators. Perhaps network
problems caused the call to disconnect.

IF Symptom

THEN What to do

Содержание Meridian

































































































































































































































































Результаты поиска

Содержание Meridian

Отзывы:

Бренды по названию

Популярные бренды

Nortel Meridian, Руководство по установке и администрированию

Результаты поиска

Содержание Meridian

Отзывы:

Бренды по названию

Популярные бренды