manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 98 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 98

98

Chapter 2 Using the console interface

320985-A Rev 01

 

System 
Characteristics...

Displays the 

System Characteristics

 screen (see 

“System Characteristics 

screen” on page 100

). This screen allows you to view switch characteristics, 

including number of resets, power status, hardware and firmware version, and 
MAC address. This screen also contains three user-configurable fields: 
sysContact, sysName, and sysLocation. When the switch is part of a stack 
configuration, this screen also displays the base unit identification, the number of 
units configured in the stack, and the local unit stack number.

Switch Configuration...

Displays the 

Switch Configuration Menu

 screen (see 

“Switch Configuration 

Menu screen” on page 103

). This menu provides the following configuration 

options: MAC Address Table, MAC Address-Based Security, EAPOL Security 
Configuration, VLAN Configuration, Port Configuration, High Speed Flow 
Control, MultiLink Trunk Configuration, Port Mirroring Configuration, Rate 
Limiting Configuration, IGMP Configuration, Display Port Statistics, Clear All 
Port Statistics, and Stack Operational Mode.

Console/Comm Port 
Configuration...

Displays the 

Console/Comm Port Configuration

 screen (see 

“Console/Comm 

Port Configuration screen” on page 223

). This screen allows you to configure 

and modify the Console/Comm port parameters, including the console port 
speed and password settings for the switch and stack operation.

Display Hardware Units

Displays the 

Display Hardware Unit Information

 screen (see “

“Hardware Unit 

Information screen” on page 233

). This screen displays the switch model and 

the software version running. The screen also displays the SPF GBIC.

Spanning Tree 
Configuration...

Displays the 

Spanning Tree Configuration Menu

 (see 

Configuring VLANs, 

Spanning Tree, and MultiLink Trunking for Nortel Ethernet Switches 
325 and 425, Software Release 3.6

(320986-A)). This menu provides the 

following options: Spanning Tree Group Configuration, Spanning Tree Port 
Configuration, Display Spanning Tree Switch Settings, Display Spanning Tree 
VLAN Membership

TELNET/SNMP/Web 
Access Configuration... 
Configuration...

Displays the 

TELNET/SNMP/Web Access Configuration

 screen (see 

“TELNET/SNMP/Web Access Configuration screen” on page 234

). This screen 

allows you to set your switch to enable a user at a remote console terminal to 
communicate with the Ethernet Switch 325/425 as if the console terminal were 
directly connected to it. You can have up to four active Telnet sessions running 
at one time in either a standalone switch or a stack configuration.

Software Download...

Displays the 

Software Download 

screen (see 

“Software Download screen” on 

page 237

). This screen allows you to revise the Ethernet Switch 325/425 

software image and diagnostics images that are located in nonvolatile flash 
memory. 

Configuration File

Displays the 

Configuration File Download/Upload

 screen (see 

“Configuration 

File Download/Upload screen” on page 240

). This screen allows you to store 

your switch/stack configuration parameters on a TFTP server. You can retrieve 
the configuration parameters for automatically configuring a replacement switch 
or stack with the same configuration when required. This screen also allows you 
to download the ASCII configuration file from a TFTP server to the switch or 
stack.

Table 14   

Console interface main menu options (continued)

Option

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов