manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 237 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 237

Chapter 6 System configuration using the Console Interface

237

System Configuration Guide

 

Software Download screen

The 

Software Download

 screens (

Figure 87

 and 

Figure 89

) allow you to revise 

the Ethernet Switch 325/425 software image and diagnostics image that are 
located in nonvolatile flash memory.

Allowed Source 
IP Address

Specifies up to 10 user-assigned host IP addresses that are allowed Telnet access to the 
CI.

Default value

0.0.0.0 (no IP address assigned)

Range

Four-octet dotted-decimal notation, where each octet is represented 
as a decimal value, separated by a decimal point

Allowed Source 
Mask

Specifies up to 10 user-assigned allowed source address masks. The remote IP address 
is masked with the Allowed Source Mask and, if the resulting value equals the Allowed 
Source IP address, the connection is allowed.

For example, a connection would be allowed with the following settings:

Remote IP address = 192.0.1.5

Allowed Source IP Address = 192.0.1.0

Allowed Source Mask = 255.255.255.0

Default value

0.0.0.0 (no IP mask assigned)

Range

Four-octet dotted-decimal notation, where each octet is represented 
as a decimal value, separated by a decimal point

Caution: 

Do not interrupt power to the device during the software 

download process. If the power is interrupted, the firmware image can 
become corrupted.

Achtung: 

Unterbrechen Sie die Stromzufuhr zum Gerät nicht, während 

die Software heruntergeladen wird. Bei Unterbrechung der Stromzufuhr 
kann das Firmware-Image beschädigt werden.

Attention: 

 Ne pas couper l'alimentation de l'appareil pendant le 

chargement du logiciel. En cas d'interruption, le programme résident 
peut être endommagé.

Table 52   

TELNET/SNMP/Web Access Configuration screen fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов