Nortel 425-24T Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 488

Nortel 425-24T Скачать руководство пользователя страница 95

Chapter 2 Using the console interface

95

System Configuration Guide

5

To return to the previous menu, press

Ctrl+R

.

6

To go to the next screen in a series, press

Ctrl+N

.

7

To return to the main menu at any time, press

Ctrl+C

.

8

Press

Backspace

to delete entered text.

You can set the options that appear in brackets. For example [Enabled].

Screen fields and descriptions

This section describes the CI screens and their fields, beginning with the main
menu.

shows a map of the CI screens.

Figure 17

Map of console interface screens

IP Configuration/Setup

SNMP Configuration

System Characteristics

Switch Configuration

Console/Comm Port Configuration

Identify Unit Numbers

Renumber Units

Display Hardware Units

Spanning Tree Configuration

TELNET/SNMP/Web Access Configuration

Software Download

Configuration File

Display System Log

Reset

Reset to Default Settings

Shutdown Command

Logout

Main Menu

MAC Address Table
MAC Address Security Configuration
EAPoL Security Configuration
VLAN Configuration
Port Configuration
High Speed Flow Control Configuration
MultiLink Trunk Configuration
Port Mirroring Configuration
Rate Limiting Configuration
IGMP Configuration
Display Port Statistics
Clear All Port Statistics

Spanning Tree
Spanning Tree Port Configuration
Display Spanning Tree Switch Settings
Display Spanning Tree VLAN Membership

Only appears when the switch is participating in a stack configuration.
Only appears when a gigabit is installed in one or more units in a stack configuration.

VLAN Configuration
VLAN Port Configuration
VLAN Display by Port
Traffic Class Configuration

MultiLink Trunk Configuration
MultiLink Trunk Utilization

BS45041F

1

1

1

2

2

MAC Address Security Configuration
MAC Address Security Port Configuration
MAC Address Security Port Lists
MAC Address Security Table

IGMP Configuration
Display Multicast Group Membership

Configuration File Download/Upload
Ascii Configuration File Download

«
...
93
94
95
96
97
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов