manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 59 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 59

Chapter 1 About Ethernet Switches 325 and 425

59

System Configuration Guide

 

Port connectors

The Ethernet Switch 325 uses 10BASE-T/100BASE-TX RJ-45 (8-pin modular) 
port connectors. 

The 10BASE-T/100BASE-TX port connectors are configured as MDI-X (Media 
Dependent Interface-crossover). These ports are connected by straight cables 
to the Network Interface Card (NIC) in a node or a server, similar to a 
conventional Ethernet repeater hub. If you are connecting to an Ethernet hub or 
Ethernet switch, use a crossover cable unless an MDI connection exists on the 
associated port of the attached device (For more information see 

Appendix B, 

“Connectors and pin assignments,” on page 425

).

The Ethernet Switch 325 uses autosensing ports designed to operate at 10 Mb/s 
(megabits per second) or at 100 Mb/s, depending on the connecting device. These 
ports support the IEEE 802.3u autonegotiation standard, which means that when a 
port is connected to another device which also supports the IEEE 802.3u standard, 
the two devices negotiate the best speed and duplex mode.

The 10BASE-T/100BASE-TX switch ports also support half- and full-duplex 
mode operation.

The 10BASE-T/100BASE-TX RJ-45 switch ports can connect to 10 Mb/s or 100 
Mb/s Ethernet segments or nodes.

For more information on RJ-45 port connectors see 

Appendix B, “Connectors and 

pin assignments,” on page 425

 for more information.

LED display panel

Figure 4

 shows the LED display panel of the Ethernet Switch 325-24G. See 

Table 3

 for a description of the LEDs.

Note: 

Use only Category 5 copper Unshielded Twisted Pair (UTP) 

cable connections when connecting 10BASE-T/100BASE-TX ports.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов