Nortel 425-24T Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 488

Nortel 425-24T Скачать руководство пользователя страница 51

Chapter 1 About Ethernet Switches 325 and 425

51

System Configuration Guide

BootP when needed as default

With Release 3.6 software, the default operational mode for BootP on the switch
or stack is now

BootP when needed

. By default, the switch or stack attempts to

use BootP if no management address is configured.

VLAN tagging enhancement

Release 3.6 software provides additional options for VLAN port tagging. Rather
than setting a port to untagged or tagged mode, you can now also choose to enable
or disable PVID tagging.

summarize the new tagging options.

The additional options are available using only the Console Interface VLAN Port
Configuration screen or the

vlan ports

CLI command. For more information,

refer to

Configuring VLANs, Spanning Tree, and MultiLink Trunking for Nortel

Ethernet Switches 325 and 425, Software Release 3.6

(320986-A).

Table 1

VLAN Tagging mode definitions

Tagging mode

Definition

PVID Tagging

Non-PVID Tagging

Untag All (Untagged Access) Disabled

Disabled

Tag All (Tagged Trunk)

Enabled

Enabled

Tag PVID Only

Enabled

Disabled

Untag PVID Only

Disabled

Enabled

«
...
49
50
51
52
53
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов