manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 428 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 428

428

Connectors and pin assignments

320985-A Rev 01

 

Figure 173   

MDI-X to MDI-X cable connections

DB-9 (RS-232-D) Console/Comm Port connector

The DB-9 Console/Comm Port connector (

Figure 174

) is configured as a data 

communications equipment (DCE) connector. The DSR and CTS signal outputs 
are always asserted; the CD, DTR, RTS, and RI signal inputs are not used. This 
configuration enables a management station (a PC or console terminal) to connect 
directly to the switch using a straight-through cable.

Figure 174   

DB-9 Console port connector

Table 165

 lists the DB-9 Console port connector pin assignments.

1

8

1

8

8

1

8

1

RX+

RX-

TX+

TX-

RX+

RX-

TX+

TX-

MDI-X port

BayStack 420 Switch

Switch or hub

Crossover cable

MDI-X port

T

R

T

R

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

BS45057B

Ethernet 325/425

5

6

9

1

619EA

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов