manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 413 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 413

Installing an SFP Transceiver

413

System Configuration Guide

 

CWDM SFP models

CWDM SFPs are transceivers that link Gigabit Ethernet ports with fiber optic 
networks. WDM technology consolidates multiple optical channels, using specific 
wavelengths to expand available bandwidth, on a common optical fiber.

CWDM SFPs are components in the optical routing system, designed to support 
high speed data communications for Metropolitan Area Networks (MANs). The 
system uses a grid of eight CWDM optical wavelengths in both ring and 
point-to-point configurations. All components are color-coded by wavelength. 

Table 157

 lists the Nortel CWDM SFPs and describes their wavelengths, color 

codes, part numbers, and cable lengths.

Note: 

The cable distance may vary depending on the quality of fiber 

optic cable used.

Table 157   

Nortel CWDM SFP transceiver list

CWDM SFP

Product number

Cable length

1470nm/Gray

•

AA1419025A

•

A1419033

•

40  KM

•

70  KM

1490nm/Violet

•

AA1419026

•

AA1419034

•

40  KM

•

70  KM

1510nm/Blue

•

AA1419027

•

AA1419035

•

40  KM

•

70  KM

1530nm/Green

•

AA1419028

•

AA1419036

•

40  KM

•

70  KM

1550nm/Yellow

•

AA1419029

•

AA1419037

•

40  KM

•

70  KM

1570nm/Orange

•

AA1419030

•

AA1419038

•

40  KM

•

70  KM

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов