manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 400 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 400

400

Chapter 12 Configuring the switch using Web-based management

320985-A Rev 01

 

Enabling and disabling autosave

The 

Configuration File Download/Upload

 pag

e 

(

Figure 164

) also allows you to 

enable and disable the autosave feature on the switch or stack.

To enable or disable autosave:

1

From the main menu, choose 

Configuration > Configuration File

.

The 

Configuration File Download/Upload

 page opens (

Figure 164

).

2

Under 

Autosave Configuration

, choose 

Enabled

 or 

Disabled

 from the 

drop-down list.

3

Click 

Submit

.

Configuring port communication speed

You can view the current console/communication port settings and configure the 
console port baud rate to match the baud rate of the console terminal.

To view current console/communication port settings and configure console port 
speed:

1

From the main menu, choose 

Configuration > Console/Comm Port

.

The 

Console/Communication Port 

page opens 

(Figure 165)

.

Console Read-Only Switch Password

Console/Comm Port Configuration

400

Console Read-Write Switch Password

Console Read-Only Stack Password

Console Read-Write Stack Password

Table 152   

Parameters not saved to the configuration file

These parameters are not saved:

Used in this screen:

See page:

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов