manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 390 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 390

390

Chapter 12 Configuring the switch using Web-based management

320985-A Rev 01

 

Table 145

 describes the items on the 

System

 page.

2

Type information in the text boxes.

3

Click 

Submit

.

Configuring switch port autonegotiation speed

You can configure a specific switch port or all switch ports to autonegotiate for the 
highest available speed of the connected station or you can set the speed for 
selected switch ports (autonegotiation is not supported on 1000 Mb/s fiber optic 
ports).

To configure a switch port’s autonegotiation speed:

1

From the main menu, choose 

Configuration > Port Management

. 

The 

Port Management

 page opens 

(Figure 160)

.

Table 145   

System page items 

Item

Range

Description

System 
Description

The factory set description of the hardware and software versions.

System Object ID

The character string that the vendor created to uniquely identify this 
device.

System Up Time

The elapsed time since the last network management portion of the 
system was last re-initialized.

Note:

 This field is updated only when the screen is redisplayed.

System Name

1..255

Type a character string to create a name to identify the switch, for 
example Finance Group.

System Location

1..255

Type a character string to create a name for the switch location, for 
example, First Floor.

System Contact

1..255

Type a character string to create the contact information for the network 
manager or the selected person to contact regarding switch operation, 
for example, [email protected]

Note:

 To operate correctly with the Web interface, the system contact 

should be an e-mail address.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов