manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 387 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 387

Chapter 12 Configuring the switch using Web-based management

387

System Configuration Guide

 

Table 144

 describes the items on the 

IP

 page.

Table 144   

IP page items  

Section

Item

Range

Description

Boot Mode 
Setting

BootP 
Request 
Mode

BootP When Needed (default)

Choose this mode to inform the 
switch to send a BootP request when 
the switch IP address stored in 
nonvolatile memory is the factory 
default value. If the stored IP address 
differs from the factory default value, 
the switch uses the stored network 
parameters. If the switch cannot find 
a BootP server, it tries five more 
times to find one and then defaults to 
the factory settings

BootP Always

Choose this mode to inform the 
switch to ignore any stored network 
parameters and send a BootP 
request, each time it boots. If the 
BootP request fails, the switch boots 
with the factory default IP 
configuration. This setting disables 
remote management if no BootP 
server is set up for the switch, but 
allows the switch to boot normally.

BootP Disabled

Choose this mode to inform the 
switch to use the IP configuration 
parameters stored in non-volatile 
memory, each time the switch boots. 
If a BootP configuration is in progress 
when you issue this command, the 
BootP configuration stops.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов