manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 381 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 381

Chapter 11 Administering the switch using Web-based management

381

System Configuration Guide

 

2

Click 

Submit

. If you do not click 

Submit

, any changes you make will be lost.

Changing the Ethernet Switch 325/425 to system defaults

You can change a standalone switch, a specific unit in a stack configuration, or an 
entire stack, replacing all configured switch parameters with the factory default 
values.

During the process of changing to default settings, the switch initiates a self-test 
that comprises various diagnostic routines and subtests. The LEDs display various 
patterns to indicate that the subtests are in progress.

To change the Ethernet Switch 325/425 to system defaults:

1

From the main menu, choose 

Administration > Reset to Default

.

The reset to default warning message displays 

(Figure 155)

.

Figure 155   

Reset to Default page message

Note: 

If you have not configured system password security, a reset 

returns you to the home page, as shown in 

Figure 72 on page 200

. If you 

have configured system password security, a reset returns you to a log on 
page (for details on configuring management passwords, see 

Configuring and Managing Security for Nortel Ethernet Switches 
325 and 425, Software Release 3.6

(320988-A)).

Caution: 

If you choose change to default settings, all configured 

settings are replaced with factory default settings when you click 
Submit. For more information about factory default settings, see 

Appendix C, “Default settings,” on page 431

.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов