manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 366 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 366

366

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

The 

Topology Table

 tab opens 

(Figure 148)

.

Figure 148   

Diagnostics dialog box — Topology Table tab

Table 139

 describes the 

Topology Table

 tab fields.

 

Table 139   

Topology Table tab fields

Field

Description

Slot

The slot number in the chassis in which the topology message 
was received.

Port

The port on which the topology message was received.

IpAddr

The IP address of the sender of the topology message.

SegId

The segment identifier of the segment from which the remote 
agent sent the topology message. This value is extracted from the 
message.

MacAddr

The MAC address of the sender of the topology message.

ChassisType

The chassis type of the device that sent the topology message.

BkplType

The backplane type of the device that sent the topology message.

LocalSeg

Indicates if the sender of the topology message is on the same 
Ethernet segment as the reporting agent.

CurState

The current state of the sender of the topology message. The 
choices are:

•

topChanged —Topology information has recently changed.

•

heartbeat —Topology information is unchanged.

•

new — The sending agent is in a new state.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов