manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 351 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 351

Chapter 9 Configuring the switch using Device Manager

351

System Configuration Guide

 

The 

Chassis

 dialog box opens 

(Figure 133 on page 344)

 with the 

System

 tab 

displayed.

3

Click the 

PowerSupply

 tab.

The 

PowerSupply

 tab opens 

(Figure 137)

.

Figure 137   

Edit Chassis dialog box — Power Supply tab

Table 133

 describes the 

PowerSupply

 tab fields.

Table 133   

Power Supply tab fields

Field

Description

Desc

The power supply type.

OperStat

The operational state of the power supply. Possible values include:

•

other: Some other state.

•

notAvail: State not available.

•

removed: Component was removed.

•

disabled: Operation disabled.

•

normal: State is in normal operation.

•

resetInProg: There is a reset in progress.

•

testing: System is doing a self test.

•

warning: System is operating at a warning level.

•

nonFatalErr: System is operating at error level.

•

fatalErr: A fatal error stopped operation.

•

notConfig: A module needs to be configured. The allowable values 
are determined by the component type.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов