manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 347 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 347

Chapter 9 Configuring the switch using Device Manager

347

System Configuration Guide

 

Table 130

 describes the 

Base Unit Info

 tab fields.

Stack Info tab

Similar to the 

Base Unit Info

 tab, the 

Stack Info 

tab provides information about 

the operating status of the 

stacked 

switches and whether or not the default factory 

settings are being used. This tab is enabled for the stacking configuration only.

To open the 

Stack Info

 tab:

1

Select the chassis.

2

From the shortcut menu, choose 

Edit > Chassis

.

The 

Chassis

 dialog box opens with the 

System

 tab displayed 

(Figure 133 on 

page 344)

.

3

Click the 

Stack Info

 tab.

The 

Stack Info

 tab opens 

(Figure 135)

.

Table 130   

Base Unit Info tab fields

Field

Description

Type

The switch type.

Descr

A description of the switch hardware, including number of ports and 
transmission speed.

Ver

The switch hardware version number.

SerNum

The switch serial number.

LstChng

The value of sysUpTime at the time the interface entered its current 
operational state. If the current state was entered prior to the last 
reinitialization of the local network management subsystem, the value 
is zero.

OperState

The operational state of the switch.

Location

Type the physical location of the switch.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов