Nortel 425-24T Скачать руководство пользователя страница 309

Страница: 309 / 488

Chapter 7 System configuration using the CLI

309

System Configuration Guide

Figure 114

displays the output from the

show lldp mgmt-sys-data

command.

Figure 114

show lldp mgmt-sys-data command output

Figure 115

displays the output from the

show lldp stats

command.

Figure 115

show lldp stats command output

show lldp port command

The

show lldp port

command displays configuration data for LLDP ports.

The syntax for the

show lldp port

command is:

show lldp [port

<portlist>

]

[neighbor] [neighbor-mgmt-addr]

[rx-stats] [tx-stats] [tx-tlv]

The

show lldp port

command is in the exec command mode.

425>show lldp mgmt-sys-data

-------------------------------------------------------------------------

lldp mgmt-sys-data

-------------------------------------------------------------------------

MgmtAddr MgmtIfId MgmtAddrOID

-------------------------------------------------------------------------

ipV4 10.128.100.100 0 1.3.6.1.4.1.45.3.57.1

-------------------------------------------------------------------------

425>show lldp stats

-------------------------------------------------------------------------

lldp stats

-------------------------------------------------------------------------

LastChange RemTable RemTable RemTable RemTable

Time Inserts Deletes Drops Ageouts

-------------------------------------------------------------------------

00:01:18.00 1 0 0 0

-------------------------------------------------------------------------

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 309 / 488

Результаты поиска

Содержание 425-24T

Отзывы: