manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 287 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 287

Chapter 7 System configuration using the CLI

287

System Configuration Guide

 

Enabling and disabling autosave

The Ethernet Switch 325/425 performs a check every sixty seconds to detect 
changes in the configuration file or a new log message in the non-volatile storage. 
If any of these two events occurs, the switch automatically saves it’s configuration 
and the non-volatile log to flash memory. Autosave also automatically saves your 
configuration information across reboots.

You can enable or disable this feature. When you disable autosave, changes in the 
configuration file are not saved to the flash memory.

This section covers the following commands:

•

“show autosave command”

•

“autosave enable command” on page 288

•

“no autosave enable command” on page 288

•

“default autosave enable command” on page 288

show autosave command

The 

show autosave

 command displays the status of the autosave feature, either 

enabled or disabled. The syntax for the 

show autosave

 command is:

show autosave

The 

show autosave 

command is in the privExec command mode.

The 

show autosave

 

command has no parameters or variables. 

Figure 107

 displays sample output from the 

show autosave

 

command.

Note: 

You can use the CLI command 

copy config nvram

 to force 

a manual save of the configuration when autosave is disabled.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов