manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 269 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 269

Chapter 7 System configuration using the CLI

269

System Configuration Guide

 

show running-config command

This command displays the current configuration of switch or a stack as a series of 
CLI commands. 

This command must be executed in the configuration mode and has no parameters 
or variables. 

The syntax of this command is:

show running-config

Figure 98

 shows the output of the 

show running-config

 

command

Figure 98   

Output of the show running-config command

425-48T(config-if)#show running-config

! Embedded ASCII Configuration Generator Script

! Model = Ethernet Switch 425-48T

! Software version = v3.6.0

enable

configure terminal

!

! *** CORE ***

!

mac-address-table aging-time 300

autotopology

no radius-server

radius-server host 0.0.0.0

radius-server secondary-host 0.0.0.0

radius-server port 1645

! radius-server key ********

telnet-access login-timeout 1

telnet-access retry 3

telnet-access inactive-timeout 15

telnet-access logging all

cli password switch serial none

cli password switch telnet none

! cli password switch read-only "********"

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов