manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 257 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 257

Chapter 7 System configuration using the CLI

257

System Configuration Guide

 

Figure 93

 displays a sample output of the 

show ip address 

command.

Figure 93   

show ip address command output

Assigning and clearing IP addresses for specific units

You can assign IP addresses for specific units within a stack. This section covers 
these topics:

•

“ip address unit command”

•

“no ip address unit command” on page 258

•

“default ip address unit command” on page 258

ip address unit command

The 

ip address unit 

command sets the IP address and subnet mask for a 

specific unit in the stack. The syntax for the 

ip address unit 

command is:

ip address unit <1-8> A.B.C.D

The 

ip address unit 

command is in the config command mode. 

Table 63

 describes the parameters and variables for the 

ip address unit 

command. 

Table 63   

ip address unit command parameters and variables

Parameters and 
variables

Description

unit <1-8>

Sets the unit you are assigning an IP address.

A.B.C.D

Enter IP address in dotted decimal notation.

425-24T(config)#show ip address unit 1

                     Configured        In Use        Last BootP

                   --------------- --------------- ---------------

Stack IP Address:  0.0.0.0                         0.0.0.0

Default Gateway:   192.168.151.1   192.168.151.1   0.0.0.0

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов