manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 220 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 220

220

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

Table 48

 describes the 

SNMP Configuration

 screen fields.

Table 48   

SNMP Configuration screen fields

Field

Description

Read-Only 
Community String

The community string used for in-band read-only SNMP operations.

Default Value

public

Range

Any ASCII string of up to 32 printable characters

Read-Write 
Community String

The community string used for in-band read-write SNMP operations.

Default value

private

Range

Any ASCII string of up to 32 printable characters

Trap #1 IP Address

1

1 The Trap IP Address and Community String fields can be set using a MIB table (in a Nortel proprietary MIB). The status 

of the row in the MIB table can be set to Ignore. If the row status is set to Ignore, the fields appear to be set when 
viewed from the console terminal; however, no traps are sent to that address until the row status is set to Valid

.

Number one of four trap IP addresses. Successive Trap IP address fields 
are numbered 2, 3, and 4. Each trap address has an associated community 
string (see Community String).

Default value

0.0.0.0 (no IP address assigned)

Range

Four-octet dotted-decimal notation, where each octet is 
represented as a decimal value, separated by a decimal 
point

Community String

The community string associated with one of the four trap IP addresses 
(see Trap #1 IP Address).

Default value

Zero-length string

Range

Any ASCII string of up to 32 printable characters

Authentication Trap

Determines whether a trap is sent when there is an SNMP authentication 
failure.

Default value

Enabled

Range

Enabled, Disabled

Autotopology

Allows you to enable or disable the switch participation in autotopology, 
which allows network topology mapping of other switches in your network.

Default value

Enabled

Range

Disabled

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов