manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 187 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 187

Chapter 4 Getting Started with Device Manager

187

System Configuration Guide

 

Types of statistics

The data tables in the statistics dialog boxes list the counters, or categories of 
statistics being gathered, for the specified object. For example, the categories for 
ports include Interface, Ethernet Errors, Bridge, and Rmon. Each category can be 
associated with six types of statistics.

Table 38

 describes the types of statistics that are available.

Types of graphs

With Device Manager, you can create line, area, bar, and pie graphs. 

Figure 64

, 

Figure 65

, 

Figure 66

, and 

Figure 67

 provide examples of different types of graphs.

Table 38   

Types of statistics

Statistic

Description

AbsoluteValue

The total count since the last time counters were reset. A system 
reboot resets all counters.

Cumulative

The total count since the statistics window was first opened. The 
elapsed time for the cumulative counter is displayed at the bottom of 
the graph window.

Average

The cumulative count divided by the cumulative elapsed time.

Minimum

The minimum average for the counter for a given polling interval over 
the cumulative elapsed time.

Maximum

The maximum average for the counter for a given polling interval over 
the cumulative elapsed time.

LastValue

The average for the counter over the last polling interval.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов