manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 121 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 121

Chapter 3 CLI Basics

121

System Configuration Guide

 

The Interface Configuration commands allow you to configure parameters for 
each port, such as speed and duplex mode. The Interface Configuration mode is 
also referred to as config-if mode.

Figure 26

 provides an illustration of the hierarchy of Ethernet Switch 325/425 

CLI command modes.

Figure 26   

CLI command mode hierarchy

You can see a specific value for each command mode at the prompt line, and you 
can use specific commands to enter or exit each command mode 

(Table 20)

. 

Additionally, you can only enter command modes from specific modes and only 
exit to specific command modes.

10194EA

User Exec

(exec)

Privileged EXEC

(privExec)

Global Configuration

(config)

Interface Configuration

(config-if)

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов