2
BASIC OPERATION
Switches
The paddle on the WT00Z-1 allows the user to:
• Turn the Associated devices on or off.
• Tapping top of switch turns the Associated device ON.
• Tapping bottom of switch turns the Associated device OFF.
Dimmers
The paddle on the WT00Z-1 allows the user to:
• Dim the Associated devices.
• Press and Hold the top of switch to increase the intensity of the Associated
device.
• Press and Hold the bottom of switch to decrease the intensity of the
Associated device.
• Tapping top of switch turns the Associated device ON to the previously set
level.
• Tapping bottom of switch turns the Associated device OFF.
LED Indication
To act as a night light, the LED on the WT00Z-1 will turn ON when the
Associated device is OFF. However, the LED can be user confi gured to turn
ON, when the Associated device is ON, if so desired. See “CONFIGURATION”
section.
Remote Control
The WT00Z-1 will respond to BASIC and BINARY commands that are part of
the Z-Wave system. Refer to your Controller’s instructions as to whether your
Controller can transmit those commands.
Associations
It is recommended that you use you Z-Wave hub’s application to create
Associations.
Removing Associations
To remove the Associations, refer to the Z-Wave Hub’s instructions on how to
remove Associations. If the Hub has not recognized the Associations, removing
the WT00Z-1 from the Z-Wave network will eliminate the Associations.
ADVANCED OPERATION
All On/All Off
The WT00Z-1 supports the ALL ON / ALL OFF commands. The WT00Z-1 can
be set to respond to ALL ON and ALL OFF commands four different ways.
Refer to your Controller for information on how to set the WT00Z-1 to operate
in the manner you desire. Some Controllers may be only able to set certain
settings of ALL ON / ALL OFF response.
The four different ways the WT00Z-1 can be setup to respond to ALL ON and
ALL OFF commands are:
1.
Responds to ALL ON or the ALL OFF command.
2.
Responds to ALL OFF command but will not respond to ALL ON command.
3.
Responds to ALL ON command but will not respond to ALL OFF command.
4.
Responds to ALL ON and the ALL OFF command.
CONFIGURATION
The WT00Z-1 supports the Confi guration command.
The WT00Z-1 simulates the operation of a dimmer. Using confi guration
commands you can adjust the dimming parameters as though it were a
dimmer. The WT00Z-1 can be confi gured to operate slightly differently than
how it works when you fi rst install it. Using the confi guration command you can
change operational characteristics.
Night Light
By default, the LED on the WT00Z-1 will turn OFF when the Associated device
is turned ON. To make the LED turn ON when the Associated device is turned
ON, set Parameter 3 to a value of 1.
Parameter Length Valid Values
Confi guration Option
3
1 Byte
0
LED OFF when the load is on, and ON when the load
is off
(default - night lite mode)
1
LED ON when the load is on, and OFF when the
load is off
2
LED is always on
3
LED is always off
4
LED blinks during RF transmissions from or to the
device
Invert Switch
To change the top of the switch to OFF and the bottom of the switch ON, set
Parameter 4 to a value of 1.
Parameter Length Valid Values
Confi guration Option
4
1 Byte
0
Top of switch is ON, bottom of switch is OFF
(default)
1
Bottom of switch is ON, top of switch is OFF
Ignore Start Level When Transmitting Dim Commands
The WT00Z-1 can send Dim commands to Associated Z-Wave enabled
dimmers. The Dim command has a start level embedded in it.
By default, the WT00Z-1 sends a command so the Associated device will start
dimming from its current dim level. However, a parameter can be set so that
the WT00Z-1 sends a command to the Associated device to start dimming from
the command’s level.
To send the start level from the WT00Z-1, set Parameter 5 to 0.
Parameter Length Valid Values
Confi guration Option
5
1 Byte
0
Dimmer starts from level sent by dim command
1
Dimmer starts dimming from its current dim level
(default)
✓
NOTE: GoControl Z-Wave enabled dimmers have the confi guration option
to ignore the start level no matter how you confi gure the WT00Z-1.
