2
Copyright © 2015 Nortek Security & Control LLC
Glass Break Detector | Installation Instructions
Glass Type and Thickness
The
minimum
size
and
shape
for
all
glass
types
is
11
x
11
in
(28
x
28
cm)
square.
Glass
must
be
framed
in
the
wall
of
the
room
or
mounted
in
a
36
in
(91
cm)
barrier.
Figure 3 Glass Type and Thickness
†
Sealed
insula ng
glass
types
are
protected
only
if
both
plates
of
glass
are
broken.
SPECIFICATIONS
Wireless
Signal
Range
300
ft
(91.44
m),
open
air,
with
Wireless
Control
Panel
Code
Outputs
Alarm;
Alarm
Restore;
Tamper;
Tamper
Restore;
Supervisory;
Low
Battery
Transmitter
Frequency
345.00
MHz
(crystal
controlled)
Unique
ID
Codes
Over
one
(1)
million
different
code
combinations
Supervisory
Interval
70
minutes
Sensor
Type
Single
microphone,
dual
stage
thud,
and
crash
Maximum
Horizontal
Sensing
Angle
360°
for
ceiling
mount
or
180°
for
wall
mount
Dimensions
(D
x
H)
4.55
x
1.9
in
(11.56
x
4.83
cm)
Weight
(including
battery
&
bracket)
5.1
oz
(144.6
g)
Housing
Material
ABS
Plastic
Color
White
Operating
Temperature
Limits
32°
‐
120°
F
(0°
‐
49°
C)
Relative
Humidity
5
‐
90%
Non
‐
Condensing
Battery
(included,
not
installed)
Two
(2)
CR
123A
3V
or
equivalent
Lithium
batteries
Approved
Glass
Break
Simulator
FG
‐
701
Glassbreak
Simulator
Certification
Anatel,
ETL,
FCC,
IC,
IFETEL,
and
NOM
REGULATORY INFORMATION
FCC Notice
This
device
complies
with
Part
15
of
the
FCC's
Rules.
Operation
is
subject
to
the
following
two
conditions:
1
This
device
may
not
cause
harmful
interference,
and
2
This
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.
This
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
B
digital
device,
pursuant
to
Part
15
of
the
FCC
Rules.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
in
a
residential
installation.
This
equipment
generates,
uses
and
can
radiate
radio
frequency
energy
and,
if
not
installed
and
used
in
accordance
with
the
instructions,
may
cause
harmful
interference
to
radio
communications.
However,
there
is
no
guarantee
that
interference
will
not
occur
in
a
particular
installation.
If
this
equipment
does
cause
harmful
interference
to
radio
or
television
reception,
which
can
be
determined
by
turning
the
equipment
off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures:
•
Reorient
or
relocate
the
receiving
antenna.
•
Increase
the
separation
between
the
equipment
and
receiver.
•
Connect
the
equipment
into
an
outlet
on
a
circuit
different
from
that
to
which
the
receiver
is
connected.
•
Consult
the
dealer
or
an
experienced
radio/TV
technician
for
help.
This
product
complies
with
FCC
radiation
exposure
limits
for
an
uncontrolled
environment.
Avoid
operating
this
product
at
a
distance
less
than
20
cm
from
the
user.
CAUTION:
Any
changed
or
modifications
not
expressly
approved
by
the
party
responsible
for
compliance
could
void
the
user's
authority
to
operate
this
equipment.
Industry Canada (IC) Compliance
This
device
complies
with
Industry
Canada
license
‐
exempt
RSS
standard(s).
Operation
is
subject
to
the
following
two
conditions:
(1)
this
device
may
not
cause
interference,
and
(2)
this
device
must
accept
any
interference,
including
interference
that
may
cause
undesired
operation
of
the
device.
Repairs
to
certified
equipment
should
be
made
by
an
authorized
Canadian
maintenance
facility
designated
by
the
supplier.
Any
repairs
or
alterations
made
by
the
user
to
this
equipment,
or
equipment
malfunctions,
may
give
the
telecommunications
company
cause
to
request
the
user
to
disconnect
the
equipment.
Users
should
ensure
for
their
own
protection
that
the
electrical
ground
connections
of
the
power
utility,
telephone
lines
and
internal
metallic
water
pipe
system,
if
present,
are
connected
together.
This
precaution
may
be
particularly
important
in
rural
areas.
Type
Minimum
to
Maximum
Thickness
Plate
1/8
‐
1/4
in
(3.2
‐
6.4
mm)
Tempered
1/8
‐
1/4
in
(3.2
‐
6.4
mm)
Sealed
Insula ng†
1/8
‐
1/4
in
(3.2
‐
6.4
mm)
