Nortek Control Mighty Mule MM571W Скачать руководство пользователя страница 43

Страница: 43 / 60

MM571W / MM572W Installation Instructions

572 Closed Limit Programming

For Pull-to-Open Applications

Step 1: Enter the secondary arm limit programming mode.

With the power on for your control box, press and hold both the

and the

buttons at the same time until

LED 3

turns on and

the buzzer sounds, and then release them.

Step 2: Program the secondary arm closed limit.

1. Next, press and hold

and you will hear a long beep and the arm will begin to extend, closing the gate. Continue holding the

button down until the gate reaches the desired closed position, and then release.

2. If you overshoot the desired closed position, you can use

to reverse the gate.

3. Adjust as needed until you are totally satisfied with the closed position. Then, press and hold

until the buzzer sounds, and

then release.

Step 3: Enter the primary arm limit programming mode.

With the power on for your control box, press and hold both the

and the

buttons at the same time until

LED 1

turns on and

the buzzer sounds, and then release them.

Step 4: Program the primary arm closed limit.

4. Next, press and hold

and you will hear a long beep and the arm will begin to extend, closing the gate. Continue holding the

button down until the gate reaches the desired closed position, and then release.

5. If you overshoot the desired closed position, you can use

to reverse the gate.

6. Adjust as needed until you are totally satisfied with the closed position. Then, press and hold

until the buzzer sounds, and

then release.

CLOSED LIMIT PROGRAMMING - PULL TO OPEN

NOTE:

If you hear three short beeps in succession, that means that the programming mode has timed out and you will

need to enter the programming mode again.

You do not have to start the positioning all over.

If the closed position is

already correct but you have timed out, press and hold

and

until the buzzer sounds, then release. Then, immediately

press and hold

until the buzzer sounds and then release.

NOTE:

If you hear three short beeps in succession, that means that the programming mode has timed out and you will

need to enter the programming mode again.

You do not have to start the positioning all over.

If the closed position is

already correct but you have timed out, press and hold

and

until the buzzer sounds, then release. Then, immediately

press and hold

until the buzzer sounds and then release.

LED 1

LED 2

LED 3

Содержание Mighty Mule MM571W





























































Результаты поиска

Содержание Mighty Mule MM571W

Отзывы:

Похожие инструкции для Mighty Mule MM571W

Бренды по названию

Популярные бренды

Nortek Control Mighty Mule MM571W, Руководство по установке

Результаты поиска

Содержание Mighty Mule MM571W

Отзывы:

Похожие инструкции для Mighty Mule MM571W

Бренды по названию

Популярные бренды