Normstahl Magic 1000, Руководство пользователя

Страница: 4 / 20

10 / 214 N000925 12/2010 Magic 1000
Please note: Check that the door is working properly
and running smoothly, and adjust if necessary. The
spring tension of the door must be set in such a way that it is
stable and can be opened and closed by hand smoothly and
without jolting.
• Standard and appropriate shock-proof socket approx. 10 -
50 cm away from the fastening position for the head of the
operator.
(For information on fuses, see the technical data.)
• Only install the door operator in dry garages.
Make sure the installation set for the connection is ready on
the door type that is being attached and/or install it according
to the relevant manual.
See instructions for installation on page ff 162.
The head of the operator can be turned by 90° to the rail
runner respectively as required (see page 162 (A)).
Installation step D, page 163:
1. Tighten the toothed belt’s clamping nut until the toothed
belt no longer rests on the guide rail (equivalent to
dimension X).
2. Use the clamping nut (dimension B) to increase the
toothed belt tension to correspond to the length of the door
operator.
Installation step G, page 165, installation dimensions:
Once installation is complete
• Slowly open the door by hand until you hear the slide snap
in.
• Connect to mains, display shows L4 and the door operator
lamp flashes at intervals of 4.
• Teach in the door operator (see Chapter 15).
• Teach in the remote transmitter (see Chapter 16).
• Carry out a safety inspection (see Chapter 9).
ATTENTION: No protection is provided by the load
switch-off whilst the door operator is being taught
in.
Note : Teaching in is only possible during initial installation or
after resetting the door operator. Do not press any keys
during the teach-in procedure.
Preparation : Connect the door to the door operator.
Teaching in with a remote transmitter
At the time of delivery and after resetting the door
operator, the remote transmitter supports the following
functions:
• A Safety control operation and fine adjustment "OPEN"
• B Safety control operation and fine adjustment "CLOSE"
• C and D Confirmation (storage)
Once the door operator has been taught
in, key A is used for remote control and
the other keys can be used to control
other similar door operators or other
radio receivers.
Teaching in
• Press and hold down key A; the door
moves in the open direction.
• When you reach the desired end position "OPEN" , release
key A. (You can make corrections with key B.)
• Press key C once briefly, teach-in procedure: The door
operator automatically stores "End position OPEN/CLOSE"
and the loads of the "Travel path OPEN/CLOSE" . The door
operator lights flash in synchronism.
Teach-in is complete when the door is open and the door
operator lights are on.
Check load switch-off according to Chapter 9,Safety
inspection.
Teaching in without a remote transmitter
On the door operator:
• Press and hold pushbutton and the door moves in the
open direction. Release pushbutton when the desired
opening position is reached. A correction can be made with
the pushbutton
.
• Press the Menu pushbutton , the door operator
automatically stores "End position OPEN/CLOSE" and the
loads of the "Travel path OPEN/CLOSE" . The door
operator lights flash in synchronism.
Teach-in is complete when the door is open and the door
operator lights are on.
Check load switch-off according to Chapter 9,Safety
inspection.
Programming the remote transmitter:
During one of the 3 status messages A, B or C (seeChapter
10), press the pushbuttons
and simultaneously
(approx. 1 s), F0 flashes in the display.
Select the desired function with the pushbuttons
and .
Press the desired key on the remote transmitter, the radio
command is taught in.
Note: The number of the function is shown in the display
during the transmission pulse.
12 Installation preparations
13 Installation
Overhead Sectional Doors
Fig
.
Low lintel Dimension G
Euro 30 - 50mm G2
G60 20 - 40mm G3
G60 Max 30 - 50mm G1
Normal lintel
Euro
100 - 120mm G2
G60 100 - 120mm G3
G60 Max 100 - 120mm G1
One-Piece-Door 20 - 40mm G4
14 Commissioning
15 Teaching in the door operator
16 Teaching in/deleting a remote
transmitter
Functions
F0 OPEN / Stop / CLOSE
F1 OPEN / Stop / OPEN
F2 CLOSE / Stop / CLOSE
F3 Stop
F4 Partial opening
F5 Light ON (restart light time)
F6 Light ON / OFF
F7 OPEN
F8 Close