Noritz ecoTOUGH NRC661-DV-NG Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 36

Noritz ecoTOUGH NRC661-DV-NG Скачать руководство пользователя страница 1

Potential dangers from accidents during installation and use are divided into the following three
categories. Closely observe these warnings, they are critical to your safety.

Prohibited

Disconnect
Power

Ground

Be sure to do

WARNING:

If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

NORITZ AMERICA
CORPORATION

Installation Manual

CONDENSING TANKLESS GAS WATER HEATER

NRC661-DV

(Indoor Installation)

DANGER indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

DANGER

WARNING

CAUTION

SBB801K-2

Rev. 04/13

Requests to Installers

• In order to use the water heater safely, read this installation manual carefully, and follow the in-

stallation instructions.

• Failures and damage caused by erroneous work or work not as instructed in this manual are not

covered by the warranty.

•

Check that the installation was done properly in accordance with this Installation Manual upon completion.

•

After completing installation, please either place this Installation Manual in a plastic pouch and

attach it to the side of the water heater (or the inside of the pipe cover or recess box if applicable),

or hand it to the customer to retain for future reference. Also, be sure to fill in all of the required

items on the warranty and to hand the warranty to the customer along with the Owner's Guide.

CAUTION

FOR USE IN RESIDENTIAL APPLICATIONS.
Installation must conform with local codes, or in the absence of
local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA
54- latest edition and/or CSA B149.1, Natural Gas and Pro-

pane Installation Code (NSCNGPIC).

Noritz America reserves the right to discontinue, or change at

any time, the designs and/or specifications of its products with

-

out notice.

CERTIFIED

R

Low NOx

Approved by

SCAQMD

14 ng/J or 20 ppm

(Natural Gas Only)

*SBB801K*

1
2
3
...
»

Содержание ecoTOUGH NRC661-DV-NG





































Отзывы:

Нет отзывов