Nordyne E3 Series and Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

background image

14

joist is not provided, use at least two sheet
metal fasteners on each duct flap.

6.

S

eal the duct flap edges with an approved

tape or compound for a leak-free joint.

Method E

1.

Apply a bead of caulking, mastic, or other
approved sealant around bottom side of 1/2”
flange and restrictor plate, when applicable.

2.

Locate the duct connector over duct and
carefully lower screw down duct connec-
tor into place.

3.

Once duct connector is located on duct,
temporarily hold in place while fastening
duct connector to the floor using flat head
screws or nails. Be sure flanges of duct
connector stay in contact with the duct.

4.

S

crew duct connector to duct making sure

a seal is made between the duct and the
duct connector. Additional screws may be
added if re

q

uired.

5.

Cut away duct along edge of duct connec-
tor flange allowing the center to drop into the
duct. Remove section of duct with caution,
as edges will be sharp.

Alcove Installation

1.

Cut alcove rough openings to minimum
dimensions shown in Figure 13.

2.

Attach frame assembly with four fasteners

Method D

1.

S

core and cut top of metal duct as indicated in

Figure 12,

S

tep 1 or

S

tep 2. If using

S

tep 1, also

cut out metal from the shaded area “A”.

2.

Fold the duct flap “B” up (see Figure 12,

S

tep 3).

3.

At the front-to-back of duct run (see Figure
12, area “A”), bend the duct connector tabs
and secure them directly to the duct.

4.

At area “B”, bend the duct connector tabs
up and back over, around the duct connec-
tor (see Figure 12, step 3).

5.

Fold/form the duct flap against the side of
the duct connector and attach as shown
(see Figure 12,

S

tep 4). Use at least three

staples on each duct flap OR... if a 2X block/

Staple Folded Duct

Flap (typ) to side of

Duct Connector

Duct

STEP 4.

Cut- Out
Area "A"

STEP 1.

"B"

"B"

Cut- Out

Area"A"

Fold Back Flap "B"

Fold Back Flap "B"

Top of Duct

"A"

"A"

"B"

"B"

Fold Back Flap"B"

Cut

Lines

Duct

Fold Back Flap"B"

STEP 2.

STEP 3.

Bend Duct Connector Tabs Up

and Over- (along length of duct)

Duct
Flap "B"

Duct

Figure 12. Alternate Duct Connector Installation D

Duct

Duct Connector

Narrow Duct

Figure 11. Alternate Duct

Connector Installation C

«
...
12
13
14
15
16
...
»

Содержание E3 Series and





































Отзывы:

Нет отзывов

Похожие инструкции для E3 Series and

Бренд: b-mola Страницы: 9

Бренд: Zibro Страницы: 2

Бренд: Linea 2000 Страницы: 48

DOLCECLIMA AIR PRO 14AC

Бренд: Olimpia splendid Страницы: 92

Бренд: Toyotomi Страницы: 38

Бренд: BASETech Страницы: 12

Бренд: Mammoth Страницы: 19

4SCU 16LS Series

Бренд: Armstrong Air Страницы: 32

Comfort Pack U Series

Бренд: National Comfort Products Страницы: 44

OmniAire 2000C Series

Бренд: Omnitec Страницы: 9

TWS-TSO26H3DVEM

Бренд: TECO Страницы: 20

Бренд: Daikin Страницы: 10

Бренд: Zodiac Страницы: 22

Бренд: Gree Страницы: 25

Бренд: Signature Страницы: 12

Ecolight 12000 UI

Бренд: Argo Страницы: 32

Бренд: Bryant Страницы: 56

Бренд: Daikin Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды