Nordson Encore HD iControl 2 Скачать руководство пользователя страница 83

Страница: 83 / 114

1609758-04

4-33

Troubleshooting

Touch Screen Failure

WARNING:

Do not spray powder with the iControl 2 console door open unless the

console opening, the door, and all externally connected devices are out of the hazardous

area surrounding any opening of the spray booth. The hazardous area extends three

feet outward from an opening and continues in a three foot arc from the edge of an

opening. Failure to observe this warning could create a hazardous condition and could

result in personal injury or property damage.

Screens Display, but Touch Function Does Not Work

If the mouse pointer on the screen does not move to wherever screen was touched, or

nothing happens buttons are touched, or the touch screen cannot be calibrated, then the

touch screen has failed. Replace the iControl 2 PC.

Temporary Fix:

Connect a USB mouse to the iControl 2 PC. You should now be able to

use the mouse to point and click on screen buttons and data fields. Replace the iControl

2 PC as soon as possible.

No Display

If the PC has power but nothing displays on the screen, then the screen has failed. You

must replace the iControl 2 PC.

Temporary Fix:

Shut off console power and connect a VGA monitor, keyboard, and

mouse to the PC ports. Turn console power on. If the boot screens and iControl 2

screens display on the VGA monitor, you can use the mouse to click on buttons and

select fields and use the keyboard to enter and change values. Replace the iControl 2 PC

as soon as possible.

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды