Nordson Encore HD iControl 2 Скачать руководство пользователя страница 30

Страница: 30 / 114

1609758-04

3-6

Installation

iControl Console CAN Address and Termination Settings

The backplane address dipswitches are set at the factory:

1. Network terminator switch SW1-3 is set to CONTINUOUS for both backplanes.
2.

Network address switches SW1-1 and 2 are set to Spray Guns 1−16 for the lower

backplane and to 17−32 for the upper backplane (if used).

SW1-1

Closed

SW1-2

Closed

Open

SW1-3

Closed: End

Open: Continuous

Guns 1-16

Guns 17-32

Slide switch

Closed

(on)

Open

Closed

(top on)

Open

(bottom in)

Rocker switch

Upper Backplane

Spray Guns 17-32

Lower Backplane

Spray Guns 1-16

SW1

Open

Figure 3-4 System Interconnect Cable Connections

Manual Spray Gun Controller Addresses

The manual spray gun controller addresses are set through software. Each controller

must have a unique address. Up to four manual spray guns can be included in a system.

Refer to the

Prodigy Manual Spray Gun Controller

manual for instructions.

NOTE:

For each HDLV pump choosen to supply powder to a manual spray gun, the

operator must enter the pump calibration numbers into the spray gun controller. Refer to

the

Prodigy Manual Spray Gun Controller

manual for instructions.

Manual Spray Gun Controller Termination

Manual spray gun controllers are shipped with their CAN termination switch set to ON.

For each manual spray gun controller in the system:

1. Open the controller enclosure and locate SW1 on the controller interface board.
2. Set the TERM switch on SW1 to OFF.

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды