Nordson ASYMTEK DispenseJet DJ-9500 Скачать руководство пользователя | Manualshive

Страница: 27 / 60

background image

Maintenance and Service

21

Cleaning the Nozzle

To clean the nozzle:

1.

Open the Stroke Adjustment Assembly (counterclockwise) until the red part aligns with the

sleeve to release the spring load on the needle assembly.

2.

Loosen the Collar/Retainer Assembly ½ turn.



The retainer will rotate to the open position.

3.

Slide the TCA off the fluid chamber.



Be careful to retain the nozzle, seat, and O-ring as they may come free.

4.

Remove the nozzle, seat, and O-ring from the fluid chamber

Figure 6-6 Nozzle, Seat, and O-ring Removal (Active Nozzle Pictured)



NOTE

The nozzle and seat are a single part on the Unitized Nozzle.

5.

Use the appropriate size nozzle cleaner to clean material from the nozzle orifice. Refer to

Table 6-1 for the correct type and size.

«
...
25
26
27
28
29
...
»

Содержание DispenseJet DJ-9500





























































Отзывы:

Нет отзывов

Похожие инструкции для DispenseJet DJ-9500

Бренд: Franke Страницы: 3

Бренд: Ultra Страницы: 52

Бренд: Bunn Страницы: 7

QUICKSOFT-DUO JQS-D

Бренд: Judo Страницы: 32

Бренд: Rinnai Страницы: 20

Бренд: Borg & Overstrom Страницы: 81

Бренд: Spectrum Страницы: 11

Бренд: Bunn Страницы: 2

Бренд: Tork Elevation Страницы: 10

Бренд: ZACK Страницы: 9

Бренд: Start Страницы: 18

TORK XPRESS H-4450

Бренд: U-Line Страницы: 6

TORK XPRESS H-1595

Бренд: U-Line Страницы: 9

Бренд: U-Line Страницы: 12

Бренд: 3M Страницы: 16

Бренд: Oasis Страницы: 3

Бренд: Zass Страницы: 12

Бренд: Halsey Taylor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды