background image

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately
informed of all warnings and precautions.

2. Use the treadmill only as described. 

3. Place the treadmill on a level surface, with at

least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill. 

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a
garage or covered patio, or near water. 

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being
administered. 

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should not be used by persons

weighing more than 350 pounds. 

8. Never allow more than one person on the

treadmill at a time. 

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. 

Always wear athletic

shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals. 

10. When connecting the power cord (see page 11),

plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord. 

11. Use only a single-outlet surge suppressor that

meets all of the specifications described on
page 11. To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-888-
825-2588 and order part number 146148, or
see your local electronics store.

12. Failure to use a properly functioning surge

suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See 
BEFORE YOU BEGIN on page 6 if the tread-
mill is not working properly.) 

15. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the
handrails while using the treadmill.

16. To protect the treadmill and TV during light-

ning storms, unplug the power cord from the
wall outlet and disconnect the antenna or
cable system. This will prevent damage due
to lightning and power line surges.

17. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid
sudden jumps in speed. 

18. The pulse sensor is not a medical device.

Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.

19. Never leave the treadmill unattended while it

is running. Always remove the key, unplug the
power cord, and switch the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 6 for
the location of the reset/off circuit breaker.)  

20. Do not attempt to move the treadmill until it is

properly assembled. (See ASSEMBLY on page
7, and HOW TO MOVE THE TREADMILL on
page 29.) You must be able to safely lift 55
pounds (25 kg) to move the treadmill.

WARNING:

To reduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

3

Содержание ViewPoint NTL24950







































Отзывы: