Nokia M1122 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 107

background image

E

Copyright Nokia Networks Oy

C33906001SE_00

2-5

D

Gateway/bridge management interface. This interface is used as a
bridge host interface or gateway interface depending on the
operation mode. In this manual it is called VBRIDGE. On the
M1122 web pages, the interface is called gateway or bridge IP
interface.

M1122 can operate in four different main modes:

D

Bridging only

D

Routing/tunneling IP only

D

Routing/tunneling IP, bridging all but IP

D

Routing/tunneling IP and bridging all, including IP

The mode in which M1122 operates depends on the configuration of
the unit’s interfaces. Table 2-1 shows the operational modes and the
corresponding interface configurations.

LAN interface

ATM VCC interfaces

Vbridge
(gateway/host inter-
face)

Bridge only

Bridging

Bridging.

Used as a manage-
ment (host) interface
for all bridged inter-
faces in case such is
needed.

Route/tunnel IP only

Routing (IP address
configured)

Routing (IP address
configured) or PPTP
local tunneling acti-
vated for each active
ATM VCC.

Not used in this case.
The unit can be man-
aged through any of
the LAN, or ATM in-
terface IP addresses.

«
...
14
15
16
17
18
...
»

Содержание M1122












































































































Отзывы:

Нет отзывов

Похожие инструкции для M1122

Бренд: ISYGLT Страницы: 7

Бренд: AudioCodes Страницы: 32

CONTROLS Series

Бренд: Condair Страницы: 16

Бренд: NETGEAR Страницы: 6

Бренд: NETGEAR Страницы: 163

Бренд: NetPurifier Страницы: 49

Бренд: HOOC Страницы: 18

Бренд: TANDBERG Страницы: 54

Internet Security Gateway ZyWALL 100

Бренд: ZyXEL Communications Страницы: 708

ADSL2+ Ethernet/USB Gateway 660RU-Tx Series

Бренд: ZyXEL Communications Страницы: 286

Бренд: Owon Страницы: 12

BEST Wi-Q WQXM-PG

Бренд: Dormakaba Страницы: 51

Бренд: Xantrex Страницы: 38

Communications gateway

Бренд: Xantrex Страницы: 70

Бренд: Technicolor Страницы: 82

Бренд: Technicolor Страницы: 81

Бренд: VBUZZER Страницы: 7

Бренд: CheckVideo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды