background image

2

DESCRIPTION

FTR970 is a radio data receiver for Nokeval MTR series wireless transmitters. It receives and 

buffers the data packets that wireless transmitters have sent. It automatically recognizes the types 

of the transmitters, so different kinds of transmitters can be used simultaneously. Transmitters can 

also have different transmission intervals. FTR970 uses license free 433.92 MHz frequency band 

(ISM) so it can be freely used, for example, almost in whole Europe.

FTR970 is housed in plastic field enclosure that provides good protection against humidity and 

dust.  The receiver is connected to a computer using RS-485 or RS-232 bus and it requires Pro-

moLog  application that reads the information from the device.

Nokeval SCL protocol is used for data transmission between the receiver and the computer. Mul-

tiple receivers can be connected in parallel to an RS-485 bus to increase the coverage area. The 

receiver has three diagnostic LEDs and it requires 8..30 VDC power supply.

Manufacturer

Nokeval Oy 

 

Tel +358 3 3424800

Yrittäjäkatu 12 

  Fax +358 3 3422066

FIN-37100 

  www.nokeval.com

Finland 

  Sales: [email protected]

 

  Technical support: [email protected]

coverage area

50...200 m

FTR970

RS-485 or RS232

PromoLog

Содержание FTR970









Отзывы: